Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
Everybody may have their unique idea about How to Install a Bathtub.
Setting up a tub isn't exactly brain surgery, but it does call for solid plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is also a moderately hard project. If the old tub is readily accessible, the project can move easily; if you have to open a wall surface to get rid of the old tub and also place the new bathtub, the job is a lot harder. In either instance, the job is within a home handyman's skills, although you will certainly need a helper to leave the old tub and also embeded in the brand-new one. See to it you have qualified yourself for the job and fit attempting it. As opposed to working with a contractor to take over a halfway-completed project, it is better to consider using one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This article will certainly assist you install a brand-new bathtub in your bathroom if you have currently acquired a brand-new bathtub as well as do not require to transform the setup of your previous supply of water pipelines.
Your tools and also product checklist should make up the following:
Planning for the Setup
Firstly, the supporting framework supplied with the bath should be fitted (if called for) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is essential to make certain that if the faucet features a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets system to stop stress on the tub.
Fit the versatile tap adapters to the bottom of both faucets using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you utilize all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its last setting.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, after that the first thing you should do is detach the supply of water. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The process of removing the existing faucets can be fairly troublesome as a result of the limited gain access to that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel prepared for the remaining water that will certainly come from the pipes. When the supply pipes have been gotten rid of, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from transforming during this process. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing substance.
Prior to carrying on to fit the brand-new faucets, compare the pipe connections on the old taps to the new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Installing the Bath tub
Using the two wooden boards under its feet, position the bathtub in the needed position. The wooden boards are helpful in equally spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four little points.
The following goal is to make sure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and also adjusting the feet on the tub till the spirit level reviews level.
To set up faucets, fit the bottom of the outermost versatile tap port to the suitable supply pipe by making a compression sign up with; after that do the exact same for the other tap.
Turn on the supply of water and also check all joints and brand-new pipework for leaks as well as tighten them if needed. Fill up the tub as well as likewise check the overflow outlet and the typical electrical outlet for leakages.
Lastly, fix the bathroom paneling as described in the maker's instruction manual. Tiling and also sealing around the tub must wait till the bath tub has been utilized at least once as this will resolve it right into its final placement.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin making certain that the washers remain in area between the faucet and the sink. Protect the tap in position with the maker supplied backnut. As soon as the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical faucet connectors. The former type needs to be linked to the faucet ends initially, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bath satisfies the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to crack a stiff seal, creating the water to permeate the wall surface in between the bathroom and also the tiling, leading to issues with wetness and also feasible leaks to the ceiling below.
You can pick from a selection of coloured sealants to blend in your fixtures as well as fittings. They are sold in tubes and cartridges, and also can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with spins of drenched paper or soft rope. Keep in mind to always fill the bathtub with water before sealing, to permit the motion experienced when the tub remains in use. The sealant can crack rather very early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise conveniently readily available on the marketplace. It is recommended to fit the tiles utilizing water-resistant or waterproof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been shown that editorial on A Step-by-Step Guide to Installing a Bathtub through a friend on our other web blog. So long as you appreciated our blog entry kindly be sure to pass it around. Many thanks for your time spent reading it.
Emergency? Call us! Report this page